Charity Golf Network

Your source for information about hosting a charity golf tournament.

Msd 6al manual

 

 

MSD 6AL MANUAL >> DOWNLOAD LINK

 


MSD 6AL MANUAL >> READ ONLINE

 

 

 

 

 

 

 

 











 

 

Page 10 of the Sniper manual under Sensor Verification, it says in bold, "If ignition box or distributor has the ability to send RPM signals with initial key on (such as Tach Sweep or REV Limiter Verification), these setting must be disabled. Reference ignition system instruction". I've looked over the MSD manual online PDF and find nothing of these features or whether it sends these signals Obsolete MSD 6AL Ignition Control With Rev Limiter. $197.89 each. $197.89. Subtotal $197.89. Add to Cart. FEATURES. Even in the harshest conditions, the 6T ignition controls deliver race winning performance to withstand severe jolts and vibrations of harsh racing, the 6T's capacitor and tra Learn More. Note: Must be used with an MSD Digital 6AL Ignition, PN 6425. GRAY TO SWITCHED 12V BLACK TO GROUND BLUE RED ACTIVATE THE 2-STEP WITH 12 VOLTS TO TACH WIRE ON MSD 6AL PN 6425 X1000 X100 ALWAYS SET THE RPM VALUE WITH THE PRINTED NUMBER ON THE HOUSING. THIS FIGURE SHOWS A SETTING OF 3000 RPM. OPERATION The Digital 2-Step Control is designed MSD 6201 User Manual Download for 1 INSTALLATION INSTRUCTIONS 1 MSD Digital 6A and 6AL Ignition Control 6A - PN 6201, 6AL - PN 6425 ONLINE PRODUCT REGISTRATION: Register your MSD product online and you'll be entered in our monthly 8.5mm Super Conductor Spark Plug Wire give-away! An MSD 6AL-2 Ignition Control will operate on any negative ground, 12 volt electrical system with a distributor. The MSD can be used with 16 volt batteries and can withstand a momentary 24 volts in case of jump starts. The Ignition will deliver full voltage with a supply of 9 - 18 volts and will operate with a supply voltage as low as seven volts. I have an MSD 85551 distributor (VR pickup) that feeds into an MSD 6AL using the magnetic-pickup input. The 6AL fires my Blaster 3 coil. I use the tach signal from the 6AL as the tach-input to my Megasquirt computer. When I crank the engine, I see the correct RPM on my Megasquirt, but I'm no longer getting any spark out of the coil. The Digital 6A and 6AL have a built in reverse polarity protection circuit. This will protect the ignition in the event of wrong connections. MSD Super HEI Kit PN 85001with MSD Digital 6AL Ignition Control 1 - Modified HEI Dust Cover, PN 8401 WARNING: During installation, disconnect the battery cables. When disconnecting the battery always The MSD box has two different input circuits; one is the White wire for Point/Amplified ignition, the other is the Green/Violet wire pair for magnetic pick-up triggers. Only one circuit should be tested at a time. If you put a jumper in the Green/Violet wire connector and tap the White wire to ground you will not get any output from the box. The Digital 6A is a microprocessor controlled, capacitive discharge ignition that multi sparks up to 3,000 RPM providing easy starts, a clean, smooth idle and quick throttle response by optimizing your engines efficiency. Above 3,000 RPM, a single spark stays lit for up to 20⁰ of crankshaft rotation ensuring a complete burn of the air / fuel MSD 6AL Ignition Module w/ Rev Control (79-11 All) Installation 1. It is a good idea to hook up the box and make sure everything works FIRST, before you mount it and splice any wires. Before starting work, remove negative battery cable first, and then remove positive cable. 2. The MSD 6AL-2 uses a high speed RISC microcontroller to control the ignition's output while constantly. analyzing the various inputs such as supply voltage, trigger signals and rpm. The high speed con-. troll

Comment

You need to be a member of Charity Golf Network to add comments!

Join Charity Golf Network

© 2024   Created by Tom King.   Powered by

Badges  |  Report an Issue  |  Terms of Service